Grandpa, here's my info from that link... Let me know what I can do...



1. Your Tweakable Settings:
Receive Window (RWIN): 65535
Window Scaling: off
Path MTU Discovery: ON
RFC1323 Window Scaling: OFF
RFC1323 Time Stamping: OFF
Selective Acks: ON
MSS requested: 1460
TTL:
(less any hops behind firewall)
130
TTL remaining: 115
TOS/TOS subfield: 0
TOS/Flags:

2. Test 783101 byte download
Actual data bytes sent: 786021
Actual data packets: 540
Max packet sent (MTU): 1500
Max packet recd (MTU): 1500
Retransmitted data packets: 2
sacks you sent: 28
pushed data pkts: 83
data transmit time: 8.704 secs
our max idletime: 2229.3 ms
transfer rate: 71108 bytes/sec
transfer rate: 568 kbits/sec
This is not a speed test!
transfer efficiency: 99%


3. ICMP (ping) check
Minimum ping: 77.70 ms
Maximum ping: 84.41 ms
Ping stability:
77.71 81.04 77.87 77.82 78.55 77.87 78.33 84.41 79.36 77.70




Notes and recommendations:
Choose RWIN between 10220 and 26280 (FAQ #586)
download/use DRTCP .. (FAQ #578)
Read the tweak FAQ

Notes and recommendations:
Good data stream (no/few rexmits)
2+ second stall detected (FAQ #1606)
test applet read too slowly
or RWIN much too small!

Notes and recommendations:
Looking good

I went to Sheilds UP ( http://www.grc.com/port_6346.htm ) and did the port test it said that it was in stealth mode. I also used the http://www3.limewire.com:6346/ and it said test worked. I havent tried any other sharing files so i dont know if they will work.

I see your RWIN is set to low for your connection you should set it between 125,000 and 130,000 for your connection speed.

Your avg ping 79 X 1.5 = 118.5 X connection sped 1085 = 128,572 is your recommended RWIN

You can download DrTCP at the link below and reset your RWIN with it you must reboot for the changes to take affect.

http://www.dslreports.com/drtcp

Also I am not exactly sure what problem you are having is you wrote But you didn't explain what your problem is. Other than one works and the other doesn't.

Although you do talk about firewall issues which leads me to believe it is connection issue. You did say one works and the other doesn't. I am assuming you are using both at home on the same connection. Check to make sure that limeWire is set up the same on both same ports etc. Your router does have a firewall in it but if one is working and the other isn't this should not be an issue unless one is using Port forward and the other isn't remember each must have a static IP address if you are port forwarding. Check and make sure.

Changing your RWIN is not going to help you to connect but it will help your data transfer speeds. I have a feeling you new computer needs to have a static IP set up on it but I am not sure you did not mention how LimeWire was set up on your work computer. But if LimeWire works on one and you are using the same connection then it should work on the other if it is setup the same.

__________________










A little common sense goes a long way

Later Grandpa

I have a desktop computer that is connected to my router/modem through a bridge. I installed limewire on it and it has no problem connecting. it shows no firewall and is turbo charged. so that narrows it down to my laptop. i also installed morpheus (on the Laptop) just to test the connection and it shows starting connection and a firewall.

Have you configured your laptop connection settings the same as your desktop. I see your router supports UPnP is you desktop set to port Forward or UPnP. Set the laptop up the same.

The link below is for setting your router/computer for Port Forward remember you must set up LimeWire and your computer up the same on all machines. If you are port forwarding each computer must have it's own static IP address.

http://portforward.com/english/route...G/Limewire.htm

__________________










A little common sense goes a long way

Later Grandpa

Let me be more clear on what my problem is: When I try to connect from my personal laptop, I get the error that my computer is trying to connect to the network. About 2 months ago I reset my wireless router (button on the back of the device) and limewire worked for the rest of that evening, but then didn't the next time I tried to use it. It just says that "connecting" message whenever I do a search.

On my work laptop (the one that LW works on) the firewall settings are set to UPnP and the "listen on port" is set to 40530, and when I set those same settings on my new personal laptop, it still doesn't work. I went to my router settings and changed it to static instead of dynamic (hopefully I did this right), and then LW stopped working on my work laptop too. Both computers starting running super slow when I opened LW also...

I wonder if my personal is not set up for UPnP? I guess I'm just pretty confused cuz I'm not too savvy on this firewalling stuff...

Also, I installed the Dr TCP program and changed my RWIN to what you suggested. Until I get LW connecting, I guess I won't know what difference it makes, but thanks for the suggestion...

I have Windows 2000...not xp and I cant connect. I tried deleting that .limewire file and that didnt work...Oh yea im connected thru a linksys router with a wireless adapter. But I disabled the firewall and limewire still said that it was on. Could there be another firewall? The router also Supports UpNp so i dunno what to do.

Also I went to the link from dragon_egg (http://www.grc.com/port_6346.htm) and it says that my 6346 port is closed. So obviously I need to open that port or use UPnP, but I thought I'd already opened the port 6346. I went to the windows firewall and put 2 exceptions on the list, one for TCP port 6346 and the other for UDP port 6346. I also went on my router's settings and followed the instructions at this link: http://support.dlink.com/faq/view.asp?prod_id=1331#604

Hopefully this info helps a bit more, thanks grandpa

boricua365

Set your router and all of your computers for UPnP do not set the listening port on limewire set it to UPnP LimeWire will find it's own port. Reset you computer connection to it's default settings.

Click on start/Control Panel/Network connections/Local area connection or whatever connection you use to connect to the Internet/Properties/Internet Properties(TCP/IP)/Properties.

Put a dot in Obtain an IP Address automatically

Put a dot in Obtain an DNS Server address automatically

Then Click OK

Attached Thumbnails

 

__________________










A little common sense goes a long way

Later Grandpa

ekfh

Your Linksys router probably has a firewall in it what model is it.
If you know how to enable UPnP in your router enable it and set LimeWire to use UPnP.

The link below may help.


http://www.gnutellaforums.com/showth...516#post179516

__________________










A little common sense goes a long way

Later Grandpa